Tuesday, October 14, 2014

3D Printing and Masonry: a Brave New World of Construction

Three dimensional printing, or 3D printing, has come a long way over the past decade or so.  This technology is growing rapidly, and holds the possibility of disrupting many conventional technologies and entire industries.  One of the conventional construction technologies facing competition from 3D printing is masonry.  Will 3D printing eventually phase out traditional masonry construction?  What are the relative benefits of each technology: masonry versus 3D printing?  How soon will the masonry industry be impacted by 3D printing?



Recent developments in the field of 3D printing include the use of concrete and concrete-like material to create objects.  These objects include both masonry-like units which are subsequently assembled into an integrated structure and also the monolithic entire structure itself, “assembled” as a whole 3D printed object.  At the forefront of this technological breakthrough are 3D printing methods such as those under development by BehrokhKhoshnevis, professor of Industrial & Systems Engineering and Civil & Environmental Engineering and Director of the Center for Rapid Automated Fabrication Technologies (CRAFT) at the University of Southern California.  Khoshnevis refers to this technology being applied to print entire buildings as “Contour Crafting.”  He and others in the field speak of very high-strength 3D printed concrete materials as being just on the horizon; material with a compressive strength of around 10,000 psi.  Currently manufactured concrete block has a minimal compressive strength of around 3,000 psi, although high-performance concretes (HPC’s) are currently available with strengths up to around 20,000 psi and higher.

The advantages of 3D printed concrete –as compared to conventional concrete- include: fairly rapid construction, the ability to make complex shapes and forms, freedom from the constraints of molding, and potentially very high strength.  These benefits may also eventually include the ability to 3D print very detailed and intricate structural features integrated into the building; including ventilation, plumbing, wiring, etc.  Other developers in the 3D printed structures include the principals of “Emerging Objects”, Ronald Rael (at University of California Berkeley) and Virginia SanFratello (at San Jose State).  Their work includes hollow, interlocking masonry like units which assemble in a manner similar to topological interlocking structures (as discussed earlier on this blog).  It holds the promise of potentially creating structural configurations suitable for seismic areas and the ability to withstand major earthquakes.

Still others are 3D printing entire homes, and appear to be close to commercialization.  Among these is a Chinese company, whose equipment is said to be capable of producing ten houses in one day.  It should be noted that these houses are not printed as a whole; they are printed in panels and these panels are then assembled.  There is also a Dutch company, Dus Architects, whose equipment is also capable of printing ‘chunks’ of house, which then must be assembled into a home.



The advantages of 3D printing should appear as obvious, namely: the ability to create virtually any shape, without the limitations imposed by a block machine, or undercuts, or draft angles; the relatively rapid pace of fabrication; a choice of materials (including plastics, concrete, and composites); and the ease of producing an object from a 3D computer file.  It would seem that the 3D printing of homes is inevitable, and that masonry will soon become a lost art - and go the way of film photography, which has been replaced by digital photography.



A few critical factors appear as though masonry will remain in the construction industry for the foreseeable future.   First of all, buildings must begin with a foundation.  In climates with freezing winters the foundation must be placed 3 or four feet below grade, or below the extent of the frost line on the coldest days.  This is simply not possible with the state-of-the-art in 3D printing technology available now.  3D printing technology cannot create a foundation below grade, although it is likely to overcome this obstacle in the future.  Secondly, most 3D printing technologies simply produce panels, or pieces or chunks of a structure which must then be assembled; this basically describes masonry, and is not an improvement over masonry per se.   Those 3D printers which are capable of producing an entire integrated, complete finished structure require an extensive working platform on which to operate.  This platform requires extensive, expensive, detailed site preparation for the 3D printer; this negates many of the so-called benefits of 3D printing an entire structure (more expensive, difficult, and time consuming).  Another major impediment to 3D printing is the fact that the construction industry is an extremely conservative industry and is very slow to accept new technologies.  This fact is made more relevant by the fickle nature of the construction consumer: people want houses, homes and buildings to look like they’ve always looked.  The 3D printing approach to providing homes still has a very long way to go before it produces houses that look very much like every house produced everywhere.  This is not an arena for brave new ideas: homeowners want their homes to look like their neighbors’.  “Fitting in” in the aesthetic sense is probably much more important than efficiency, strength, environmental concerns, longevity, or any other factor about construction.  The appearance of the finished product cannot be overemphasized, and 3D printing has a long way to go here.  Finally, and perhaps most importantly, is the factor of cost.  While 3D printer advocates say that they are faster and less expensive than masonry, it is instructive to note that the concrete block manufacturing industry has developed to a state of high efficiency and economy.  An 8 inch x 8 inch x 16 inch rectangular concrete block is produced in around 2 seconds, and typically costs around $1.00 or so.  This is the benchmark to beat, and 3D printing is not anywhere close to this, despite the claims being made.  It appears as though concrete block will probably be around for a while yet.



3D printing holds great promise for the future of construction.  Those who assume that it will never affect their industry (designers, builders, blockmakers, masons, etc.) do so at their own extreme risk; they are likely to go the way of film photography, i.e., extinction.  Instead, it appears inevitable that 3D printing will have a huge transformative effect on construction in general and on masonry in particular.  It seems that masonry will –in all likelihood- always exist, but that it will be fundamentally transformed by 3D printing.  Masons can design their work and have custom blocks produced on-site, instantly and inexpensively.  Brunelleschi would have put 3D printing of masonry to spectacular use; he wouldn’t have had to carve shapes from turnips to show his masons how he wanted block made.  They would be made instantly, exactly as he envisioned them.  It seems that 3D printing could well add to the art, science and craft of masonry in the relatively near future.

8 comments:

  1. I think it is cool to take a general overlook at masonry and all it does to help the community. Without masonry, we wouldn't have such strong foundations in homes and other things like that. I hope that 3D printing continues to be researched as well, since I also think it could be very helpful to the future of masonry. http://www.mblandscape.com/masonry-stone-pavers-new-york-rockland-county.html

    ReplyDelete
  2. I never really got into masonry. I did always think that it was pretty cool on what kind of things you can make with masonry. I am starting a project at home where I think that I will be needing to hire a masonry contractor here in Kelowna. I think that there is one around where I live. http://www.mweissmasonryinc.ca/en/

    ReplyDelete
  3. 3D printing is the future of manufacturing. Everything from food to home is 3D printed with great precision. It not only saves time, but material as well. Walls are so smooth that it doesn’t require any masonry work. I guess it’s going to mar concrete and masonry contractors’ business.

    ReplyDelete
    Replies
    1. It's an interesting situation Bob, because the construction industry is traditionally extremely conservative and slow to accept new ideas. I think the adaptation of 3D printing by the construction industry will occur slower than 3D printing's abilities will be realized. Masonry companies must adapt eventually, or perish. I expect that eventually hand-crafted masonry will become a specialty market, but not for at least ten, maybe twenty years. Thnaks for your comment.

      Delete
  4. Now a days, masonry work for construction is getting a new look. Loved it. Thank you for the post. Its a great experience to read this. I think http://nypavingandmasonry.com/ will be found to be useful.

    ReplyDelete
  5. We never know what the future will hold. 3D printing could impact masonry significantly, but it also could take an entire new direction. Masons might have to adapt, but really, we are not sure how 3D printing will be in 5 or 10 years. http://www.mweissmasonryinc.ca/en/

    ReplyDelete
  6. I like all details that you provide in your articles. eddm mailer printing

    ReplyDelete
  7. Good one you explain. all building and civil related work to must use for the pre engineering process is very well done to introduce. Majorly access material is boom lift rental for access and tools used for core work. Thanks for the opportunity. and Thanks for post and creadited to Sendhamarai Engineering.

    ReplyDelete